Cerber C52 is a burglar alarm system with 6 fully programmable zones on the motherboard, expandable to 12 by doubling and / or using keypad zones (each. Cerber c Users Guide – Download as PDF File .pdf), Text File .txt) or read online. Cerber C Zone and 2-Partition Burglary Control Panel For your home and office User’s Guide Doc / / version 1. INTRODUCTION.

Author: Tautaxe Akinolabar
Country: Colombia
Language: English (Spanish)
Genre: Music
Published (Last): 19 February 2015
Pages: 135
PDF File Size: 1.64 Mb
ePub File Size: 11.16 Mb
ISBN: 128-5-26147-578-7
Downloads: 4449
Price: Free* [*Free Regsitration Required]
Uploader: Faekree

In case of a monitored alarm system, authorities may not respond appropriately.

cedber Any alarm system, whether commercial or residential, is crrber to compromise or failure to warn for a variety of reasons. The user code must have the right for arming. Section [] — Walk Test service mode The control panel will no longer consider the detectors from a bypassed zone.

This trouble indicator will appear if wiring between the siren and the control panel is shorted, cut-off or there is an overload on the siren control wire a 3K3 resistor must be connected across the bell terminals. This trouble indicates that the battery is disconnected or its voltage is lower than The following operations can be performed: Only zone 1 LED Blinking That means the selected user code, the follow me phone number or the system time and date are not programmed and the control panel is waiting for first digit group for respective option.

The user code must have the cerbsr siren stopping right; After entering the first code digit, the continuous beep will stop and upon each key pressing, the keypad buzzer will sound a short cerver beep.

This means that user was under duress ambush.

Cerber c612 Users Guide

Passive Infrared Detectors do not provide volumetric area protection. The list of messages that can be seen on the LCD keypads display is much longer, but easy to understand.


This alarm system should be tested weekly to make sure that all sensors work properly. If any trouble condition occurs, it needs to be solved before arming to assure a proper function for system. Press the keys from 1 to cerer to view the order of the first 9 alarms x612 in the system since last arming.

The 2nd to 45th user codes c621 not programmed by default. The 1 to 5 options will be displayed according to the table bellow: Even persons who are awake may not hear the warning if the alarm is muffled by noise from a stereo, radio, air conditioner or other appliances, or by passing traffic. The master user only may see own rights as they were established by the installer previously and, if the master user wants to change his rights he must call his installer.

If the feature is got activated, the keypad buzzer will beep for 3 times and, if it is got deactivated, the keypad buzzer will sound a long beep. The system time and date programming is allowed to the master user only if the appropriate option does not disabled by programming see the appropriate option within [] section.

In a partitioned system, in order to stay arm a partition, by users assigned to only one partition, simply key in a valid user code within one of the previous sequences; the corresponding partition will stay arm.

Programming of the system time and date can be canceled by [ ] key pressing. Section [] – Manually Activation of PC callback Entering section [] allows to the installer to manually initiate the PC call to establish the communication between the control panel and PC.

Moreover, smoke detectors have sensing limitations. The BELL output uses a fuseless circuit and it will automatically shut down if the current exceeds 2.

If first option in this section is set as enabled, then, upon occurring in the system of some alarm events, the control panel will automatic initiate the reporting on the phone line of these events and the system status, too, by voice messages or by synthesis sounds, specific to these events.


A second floor detector, for example, may not sense a first floor or basement fire. Thus, the dispatcher will be informed that the user action was performed under threat. If [8] key is pressed and the zone 3 LED is blinking, then the 8-th memorized alarm was triggered by zone 3.

In a partitioned system entering a user code with the right of siren stopping, while siren is sounding, the following conditions will apply: Once a delayed zone is first violated during one armed period it will start the appropriate entry delay timer; the keypad buzzer will sound a continuous beep, indicating that the system must be disarmed. For each these times any value from to may be entered, but the panel will automatic adjust the introduced value by modulo and will record the result in memory as programmed value.

Program the inactivity autoarming time as it ceber described in [] section.

Cerber c Users Guide – Documents

After [ ] key was pressed, the keypad buzzer will sound 6 confirmation beeps and exit this section waiting for a new command to enter another section or [ ] key to exit the main programming menu.

They do not create multiple beams of protection and intrusion can only be detected in unobstructed areas covered v612 the beams. While PC modem is calling the control panel, just entering this command will manually activate the communication between PC ccerber panel.

Quick arming features are allowed only if the appropriate options are enabled by programming in section []. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers.